Which circle does a beam angle describe?
A beam angle describes directions from a light, rather than the edge of a uniformly lit patch. ERCO defines its emission angle between the directions where intensity falls to 50% of the value in the main beam direction. That is an intensity definition: it does not say that the illuminance across the corresponding circle is constant, or that it meets a task’s required light level.
For a circular, symmetric beam, those directions form an ideal cone. A plane perpendicular to its axis cuts the cone in a circle. The geometric diameter and area above describe that circle for your stated angle and distance. Light may extend beyond the angle-defined outline.
Check the definition supplied with the product. A field angle, a half-angle and a pair of asymmetric angles describe different things. A pair such as 60° × 90° cannot be represented by the one circular angle used here. Recording a beam angle in the Lighting Product Comparison preserves a product statement; it does not independently verify the distribution.
Why do angle and distance change the outline?
Take a cross-section through the centre of the ideal cone and divide it along its axis. The resulting right triangle has half the full beam angle at the light, distance h along the axis, and circle radius r opposite the half-angle. The right-triangle tangent relationship gives:
r / h = tan(θ / 2)
So the circle’s diameter is D = 2h × tan(θ / 2), and its area is A = π(D / 2)². Here θ is the full angle in degrees, h and D are in metres, and A is in square metres. The numerical calculation converts the half-angle to radians before evaluating tangent.
Moving the target plane
At a fixed angle, doubling the distance doubles the diameter and quadruples the area. The radius is proportional to distance; the area depends on its square. This describes geometry, not a prediction of actual lux across the plane.
For a bench below a ceiling light, h is the axial distance from the light to the bench plane. Using floor-to-ceiling height instead changes the plane being described. If the light is aimed obliquely at the bench, the perpendicular-plane model no longer applies.
Widening the full angle
At a fixed distance, a wider angle produces a wider circle. The change follows tangent, so doubling the angle does not generally double the diameter. Near 180°, very small angle changes can produce very large geometric circles. That sensitivity makes the angle definition and input precision particularly consequential; it does not imply useful lighting over such an area.
Compare three ideal geometries
These are artificial geometries, not product ratings or recommended mounting arrangements. Each assumes a circular symmetric cone, no obstruction and a plane perpendicular to its axis.
For the first row, the half-angle is 45° and tan(45°) = 1. The radius is 2 m, the diameter is 4 m and the area is 4π m². Moving to 4 m gives area 16π m². For the last row, tan(30°) = 1/√3, giving a diameter of 2√3 m and an area of 3π m².
Display values are rounded to two decimal places; the area uses the unrounded radius. Positive results below 0.01 are shown as “<0.01” with their unit, rather than as zero. The displayed precision does not improve the precision of a manufacturer’s angle or a measured distance.
What does the area help you decide?
The circle helps you understand the size implied by an angle and a perpendicular distance. It can reveal that a proposed geometric outline is larger or smaller than an object you have measured. It cannot establish that the object will be lit sufficiently, or evenly.
Illuminance, glare, shadows, reflected light and the overlap between multiple lights require further information about the source, distribution, placement and surroundings. Treating adjacent circles as evenly lit discs would lose those distinctions. This tool therefore gives neither a recommended spacing nor a number of lights for a room.
FAQs
Can I use a tilted beam or a rectangular distribution?
The ellipse mode supports a circular symmetric cone meeting a flat tilted plane. Asymmetric optics or rectangular distributions still need their own geometry and product photometry; averaging two beam angles does not create a circular cone.
Does a 50% intensity outline mean 50% illuminance on the surface?
No. The angle definition compares intensity in different directions from the source. Illuminance on a plane also depends on distance and incidence angle. The geometric circle alone supplies none of those illuminance values.
A tilted cone makes a finite ellipse only within a boundary
Let a be half the full cone angle, b the beam-axis tilt measured from the receiving plane’s normal, and d the distance along the beam axis to its intersection with the plane. The shortest source-to-plane separation is h = d cos b. A finite ellipse requires a + b < 90°; at grazing incidence the cone no longer makes a bounded ellipse on the plane.
Define A = cos(a + b) cos(a − b). Substituting the plane into the circular cone equation and completing the square gives:
- Major diameter: 2h sin a cos a / A.
- Minor diameter: 2h sin a / √A.
- Ellipse area: π × major diameter × minor diameter / 4.
- Centre offset from the axis/plane intersection, towards the far side: h sin b sin²a / (A cos b).
These expressions are a geometric derivation, not a lighting-performance rule. For a hypothetical 60° full cone, 30° axis tilt and 2 m axial distance, h = √3 m. The two edge rays in the tilt section strike at plane coordinates 0 and 3 m from the normal foot, while the axis strikes at 1 m. The ellipse therefore has a 3.00 m major diameter, √6 ≈ 2.45 m minor diameter and centre 0.5000 m beyond the axis intersection. Its area is 3√6π/4 ≈ 5.77 m². At zero tilt the expressions reduce to the perpendicular circle. As the boundary approaches grazing, the geometric footprint becomes very large; that says nothing about useful illuminance at its distant edge.