Uniform Cone Luminous Flux

Calculate solid angle and luminous flux inside an ideal circular cone with constant intensity throughout it.

Calculate the flux inside an ideal circular cone with constant luminous intensity in every direction within it. This is a model calculation, not a conversion from a real beam angle and peak candela.

Results update as you edit.

Calculating needs JavaScript. The form becomes available when its script is ready; the guide below is always readable.

Calculation inputs

Calculation inputs
Greater than 0° and no more than 180°. This tool supports a cone up to a hemisphere; the angle is twice its axial half-angle.
Finite and zero or more. This is the same intensity in all cone directions, not a measured peak for a varying distribution.
The computed lumens belong to the cone. They equal the model’s total output only if there is no emission outside that cone.

Continue your task

Interpret sr and lm within the declared cone; this is total model output only if there is no light outside it.

If this answers your question within the model’s limits, record the original inputs, unrounded result and conditions. Otherwise choose an action only when its condition applies:

See this task in the decision tree

Opening another tool does not transfer or store your entries. Keep the original values, units and conditions with the next calculation.

Flux within a cone depends on its solid angle

Luminous intensity in candela describes luminous flux per solid angle in a direction. If that intensity is constant throughout a specified cone, its flux is lumens = candela × steradians. The RP Photonics explanation of luminous intensity describes this directional quantity and uniform emission.

A solid angle describes a portion of the directions around a point, rather than an area on a bench. MathWorld defines it using the area on a unit sphere and gives the spherical-coordinate integral. Integrating over all directions within a circular cone gives Ω = 2π[1 − cos(θ/2)], where θ is the full cone angle. This tool supports θ greater than 0° and no more than 180°; at 180° the cone covers a hemisphere, with solid angle 2π sr.

Distance does not enter this calculation. Moving a receiving plane farther away spreads the same cone flux over a different area; it does not change how many directions the cone covers. The beam geometry calculator separately explores an angle-defined circle at a specified distance.

An ideal 120° cone at 100 cd

For an artificial uniform model, let the full cone angle be 120° and intensity be 100 cd in every direction inside it. The half-angle is 60°, and cos 60° = 0.5:

Ω = 2π(1 − 0.5) = π sr.

Cone flux = 100π lm = 314.16 lm, rounded to two decimal places. The displayed solid angle is 3.1416 sr; that display rounding is not used to compute the flux.

Artificial uniform model Solid angle (sr) Flux at 100 cd (lm)
60° full cone 0.8418 84.18
120° full cone 3.1416 314.16
180° full cone 6.2832 628.32

Widening the cone while holding intensity fixed increases the flux because more directions carry that intensity. Flux is not proportional to the angle in degrees. Holding angle fixed and doubling the constant intensity does double the cone flux.

Why a real beam angle and peak candela are insufficient

A real luminaire usually has a varying intensity distribution. Its peak candela describes one direction, while its stated beam angle describes a boundary under the manufacturer’s angle convention. It does not establish constant intensity across the cone, nor zero output outside it. Multiplying that peak by the calculated solid angle therefore does not recover measured total lumens.

This result is the flux inside the ideal cone. It equals the ideal source’s total output only if no light is emitted outside that cone. Real total flux requires integration of the applicable distribution or suitable measured data. To estimate direct illuminance at one point using a known intensity in that specific direction, use point-source illuminance with its distance, incidence-angle and point-source conditions.

Related tools

Beam Spread Geometry

Solve ideal circular beam geometry on a perpendicular plane, or a tilted cone’s finite ellipse. Geometry does not establish lighting adequacy.

Inputs and results
Inputs
Full cone angle, axial distance or perpendicular diameter; tilted-ellipse mode also requires axis tilt from the plane normal.
Results
Conditional circle geometry, or ellipse major/minor diameters, area and centre offset.

Point-source Illuminance

Estimate direct point illuminance from directional candela, add compatible sources, or scale a measured direct contribution by distance.

Inputs and results
Inputs
Directional intensity in cd, source-to-point distance in m and incidence angle from the normal in degrees.
Results
Direct illuminance in lx at the specified point, with model conditions.

Browse all lighting tools