Mired Shift Calculator

Find the signed mired change between two CCT values or apply a supplied nominal reciprocal-temperature shift.

Express source and target correlated colour temperatures on the reciprocal-temperature scale, or apply a supplied nominal filter shift. No filter catalogue or product recommendation is inferred.

Results update as you edit.

Calculating needs JavaScript. The form becomes available when its script is ready; the guide below is always readable.

Calculation inputs

Calculation inputs
Both directions use the unrounded reciprocal values.
Finite kelvin value greater than zero. Use measured or specified CCT under the source/product conditions.
Greater than zero. A target value alone does not establish that a particular filter can achieve it.
Signed decimal: positive lowers nominal K; negative raises it. Verify the manufacturer’s source/filter conditions. Source mired plus this shift must remain positive.

Continue your task

Interpret the mired change without assuming a particular filter achieves it on an arbitrary LED spectrum.

If this answers your question within the model’s limits, record the original inputs, unrounded result and conditions. Otherwise choose an action only when its condition applies:

See this task in the decision tree

Opening another tool does not transfer or store your entries. Keep the original values, units and conditions with the next calculation.

Why a kelvin difference is not a filter shift

The reciprocal colour-temperature scale expresses mired = 1,000,000 ÷ CCT in kelvin. Equal changes on this scale do not correspond to equal kelvin differences. For example, a shift from 5000 K to 4000 K is 200 to 250 mired, giving +50 mired. The same +50 mired applied to 3200 K gives approximately 2758.62 K, rather than a further 1000 K reduction.

For a source and target, the signed shift is Δmired = 1,000,000/target K − 1,000,000/source K. A positive shift gives a lower nominal CCT; a negative shift gives a higher nominal CCT. A 3200 K to 5600 K change gives −133.928571… mired, displayed as −133.93 mired.

CCT means correlated colour temperature, a description of light colour relative to a reference locus. It is not the physical temperature of the LED, lamp housing or filter.

Applying a nominal manufacturer shift

With a known source CCT and supplied nominal shift, the inverse arithmetic is target K = 1,000,000 ÷ (source mired + shift). The denominator must remain positive. At 5000 K the source is 200 mired: a shift of −200 would give a zero denominator, not a finite temperature; a more negative value would not give a valid positive kelvin result.

LEE’s colour-temperature tool and filter records illustrate why nominal values and source conditions matter. The 204 Full CTO record describes 6500 K to 3200 K with a nominal +159 mired shift. The exact reciprocal difference between those two stated temperatures is approximately +158.653846 mired. Applying exactly +159 mired to exactly 6500 K gives approximately 3196.46 K. The small discrepancy follows from rounded product values; the calculation does not force them to agree.

Internal calculations use the entered values at full available precision. The displayed mired shift is not rounded and then fed back into the inverse calculation. Ordinary displayed values use two decimal places, so a product specification’s own measurement uncertainty and rounding still matter.

A reciprocal shift does not describe the whole spectrum

A source CCT and nominal filter shift provide reciprocal-temperature arithmetic. They do not supply the source’s spectral power distribution or the filter’s wavelength-dependent transmission. An arbitrary LED and filter combination can therefore differ from a result obtained under the manufacturer’s stated source conditions.

Green–magenta tint, CRI and other spectral properties are separate from this one-dimensional change. Averaging two lights’ kelvin values, or averaging their mired values, does not predict the colour of their mixture. A measured spectrum and an appropriate colourimetric method are needed for that different task. If a filter also has neutral-density loss, the Exposure and ND Calculator can apply a separately supplied attenuation to the camera settings; mired shift alone does not specify that attenuation.

Related tools

Lighting Product Comparison

Compare two products and calculate luminaire efficacy, or convert lumens and input watts using a supplied matching efficacy.

Inputs and results
Inputs
Product specifications; conversion requires a supplied luminaire lm/W value, known lm or W and matching-data conditions.
Results
A side-by-side record and conditional lm/W; a separate conversion calculates lm or W under your supplied efficacy.

Exposure and ND Calculator

Solve shutter time, aperture or ISO after an ND change, and convert cine frame rate and shutter angle to exposure time.

Inputs and results
Inputs
Baseline and target camera settings, absolute ND losses or transmission stacks; optional cine fps and angle.
Results
Equivalent settings, ND transmission/density, setting EV and distinctly labelled unfiltered-scene equivalent EV100.

Browse all lighting tools