Rectangular Lighting Grid Geometry

Calculate an equal-cell grid, axis coordinates and spacing-to-height ratios. Geometry supplies no lighting adequacy verdict.

Divide a rectangle into equal cells and place a point at each centre. The half-cell perimeter offsets are a geometric choice, not a spacing recommendation.

Results update as you edit.

Calculating needs JavaScript. The form becomes available when its script is ready; the guide below is always readable.

Calculation inputs

Calculation inputs
Positive inside dimension, measured from the chosen origin corner.
Positive dimension perpendicular to the x axis.
A whole number from 1 to 100. One row is centred across the width.
A whole number from 1 to 100. One column is centred along the length.
Positive separation, not total floor-to-ceiling height unless the floor is the relevant plane.
The tool supplies no manufacturer spacing limit or pass/fail rule.

Continue your task

Record coordinates, point count and spacing-to-height ratios for a geometric sketch; a ratio has no automatic pass threshold.

If this answers your question within the model’s limits, record the original inputs, unrounded result and conditions. Otherwise choose an action only when its condition applies:

See this task in the decision tree

Opening another tool does not transfer or store your entries. Keep the original values, units and conditions with the next calculation.

An equal-cell grid starts with a coordinate convention

This tool divides a rectangle into a chosen number of rows and columns, then places one point at the centre of each cell. It is a coordinate worksheet: the row and column counts come from you, and the half-cell edge offsets are part of this geometric construction. They are not recommendations for luminaire spacing.

Choose one corner as the origin. The x axis runs along the entered length L, and the y axis along the width W. With c columns and r rows:

Cell length = L/c; x centre i = (i + ½)L/c, for i = 0 to c − 1.

Cell width = W/r; y centre j = (j + ½)W/r, for j = 0 to r − 1.

Every combination of an x centre and a y centre is one grid point, giving r × c points. The tool supports 1–100 cells on each axis and uses metres, consistent with the SI length definition.

A 15-point artificial grid

Take a 10 m long, 5 m wide rectangle, five columns along x and three rows along y. The x cell length is 2 m, so the centres are 1, 3, 5, 7 and 9 m from the origin. The y cell width is 5/3 m, so the centres are 0.8333, 2.5000 and 4.1667 m after display rounding.

This describes 15 coordinate pairs. For example, the first x centre combines with each y centre to give (1, 0.8333), (1, 2.5000) and (1, 4.1667) m. The edge offsets are half of the corresponding cell dimension.

What spacing-to-height means here

If the declared height above the working plane is 2 m, adjacent x spacing divided by height is 2/2 = 1.0000. The y ratio is (5/3)/2 = 0.8333…. These are arithmetic ratios, with no built-in acceptable limit.

A single row or column still has a centre, but no adjacent pair on that axis. Its adjacent spacing and spacing-to-height ratio are therefore reported as not applicable, rather than treating the full room dimension as an actual separation between two lights.

Check the sketch against the physical task

Use room and working-plane geometry to keep the height reference consistent. The lumen-method tool can provide an arithmetic count under declared factors, but a count alone may not factor neatly into a useful rectangular grid. Changing the arrangement can change the applicable utilisation data.

Ceiling structure, furniture, shadows, photometry, glare and installation requirements can prevent a regular geometric grid from being suitable. A grid that fits inside the rectangle does not demonstrate lighting adequacy. Likewise, these point coordinates are not an approved measurement grid. Sample statistics require equally representative readings under consistent conditions; choosing where to measure remains a separate task.

Coordinates and ratios display to four decimal places. Retain the original dimensions and use appropriate real-world measurement precision rather than treating four printed decimals as installation accuracy.

Related tools

Room Index and Working-plane Geometry

Calculate rectangular area, luminaire-to-plane height and room index from dimensions measured on a common basis.

Inputs and results
Inputs
Room length and width, source and working-plane heights in m, with a shared level datum.
Results
Area in m², height above the working plane in m and dimensionless room index K.

Circular Beam Overlap Geometry

Find the intersection and union of two geometric circles from their diameters and centre separation.

Inputs and results
Inputs
Two circle diameters and centre-to-centre separation in m, on the same plane.
Results
Overlap and union in m², plus overlap as a percentage of each circle.

Lumen Method Estimate

Estimate average maintained illuminance with declared UF/MF, or use a separate supplied photon-delivery budget for average PPFD and count.

Inputs and results
Inputs
Working-plane area in m², initial whole-luminaire lm, UF/MF fractions, count or target lx, and recorded assumptions.
Results
Conditional average maintained lx, or a rounded-up luminaire count and its modelled average.

Illuminance Sample Statistics

Summarise spatial lux or PPFD samples with a supplied reference, or describe daylight occupied-time coverage with missing periods kept explicit.

Inputs and results
Inputs
Same-basis spatial lux/PPFD and represented areas, or daylight-only zone/time records, occupied horizon and user threshold.
Results
Spatial descriptive statistics and reference shares, or daylight area-time coverage bounds, observed mean and recorded exposure.

Browse all lighting tools