LED Strip Reel Planner

Round varied runs to permitted cuts and allocate continuous pieces to usable leftovers and new matching reels.

Allocate different whole strip runs to matching usable leftovers and new stock reels. Every run remains one continuous piece; the plan assumes no splices and no cutting loss.

Results update as you edit.

Calculating needs JavaScript. The form becomes available when its script is ready; the guide below is always readable.

Calculation inputs

Calculation inputs
One comma-separated pair per line. Positive target length and whole count, at most 18 runs after counts are expanded.
Optional; blank means no existing stock. At most 12 pieces. Each length must start at a permitted cut origin and contain a whole number of cut intervals.
Positive matching stock length, containing a whole number of permitted cut intervals.
Positive interval for this product and cut origin. Do not infer it from LED spacing or supply voltage.
The same rule applies to all rows. A floor result of zero intervals is rejected as an unfulfilled run.
Identify one matching product, cut interval, usable lengths and permitted cut origins. Check connector allowances and maximum connected lengths separately.

Continue your task

Review each allocation and unmet run. A feasible arrangement is labelled minimum only when the bounded method proves it.

If this answers your question within the model’s limits, record the original inputs, unrounded result and conditions. Otherwise choose an action only when its condition applies:

See this task in the decision tree

Opening another tool does not transfer or store your entries. Keep the original values, units and conditions with the next calculation.

Total metres do not determine the reel count

Suppose an invented project needs two 4 m runs and one 2 m run, all cut from 5 m reels without joining pieces. The required total is 10 m, but two reels cannot supply it. Each 4 m run occupies its own reel and leaves only 1 m; neither remainder can supply the continuous 2 m run. Three reels are required, leaving 5 m spread across their remaining pieces.

The ratio of total required length to reel length, rounded up, is only a lower bound. It ignores the way whole runs must fit into individual pieces. Adding existing leftovers can reduce purchases, but only when their continuous usable lengths fit the required cuts.

Artificial requirement Existing usable stock New 5 m reels One complete allocation Total remaining stock
4 m, 4 m, 2 m None 3 [4], [4], [2] 5 m
3 m, 2 m, 2 m, 1 m None 2 [3 + 2], [2 + 1] 2 m
3 m, 2 m, 2 m, 1 m One 3 m piece 1 Existing [3]; new [2 + 2 + 1] 0 m

The examples assume matching strip, permitted cuts at those lengths, no splicing and no cutting loss. A combined remainder is a stock account, rather than one continuous piece. Keep the per-piece remainder list for later use; two 1 m pieces cannot become one 2 m run under this model.

Round every run before allocating stock

A required length may fall between the manufacturer’s permitted cut marks. For cut interval δ in metres and target T, the supported choices are:

  • Do not exceed the target: cut length = δ × floor(T/δ).
  • At least reach the target: cut length = δ × ceil(T/δ).

The same rule applies to every requested row. Enter the interval in millimetres; the exact conversion is δ = interval/1,000. The rounding calculation is shared with the LED Strip Cut Length tool, so allocation uses the actual cut length rather than the unrounded target. For an artificial 4.37 m target and a 50 mm interval, the shorter rule supplies 4.35 m and the longer rule supplies 4.4 m. Their respective 0.02 m shortfall and 0.03 m excess remain part of the run specification.

Use the interval for the actual product. ENTTEC’s specified 50 mm interval for one particular pixel strip illustrates why the permitted cuts come from the product information; it is not a general interval for all LED strips. LED spacing and supply voltage alone do not establish cut positions.

A run which rounds down to zero whole intervals is rejected as unfulfilled. Selecting the longer rule can produce a physical piece, but it may then exceed a confined space. Connector dimensions, end caps, cable entries and mounting clearances must be allowed for when establishing the usable target and stock lengths.

The stock must share a usable cut origin

All entered stock must be the same compatible strip product. A leftover length is usable only from a permitted starting point, with an exact whole number of the supplied cut intervals. A damaged end, missing connector allowance or arbitrary mid-section measurement cannot silently become usable stock. Adjust the available length to a verified usable piece before allocating it.

Each required run is assigned wholly to one existing piece or one new reel. The planner never joins short remainders. If a run is longer than every available continuous piece and the new reel length, it is listed as unmet. Increasing the number of short reels will not resolve that length requirement.

An allocation accounts for lengths, not physical cutting order or installation suitability. Keep maximum connected run lengths and manufacturer installation conditions separate. An electrical limit can make a geometrically possible strip run unsuitable; this planner does not choose power supplies, wiring, protection or voltage-drop allowances.

Read the optimisation status with the allocation

For supported inputs, an exact search tries to minimise the number of new reels while allowing use of existing stock. The result is labelled minimum proved only when the search has exhausted the relevant alternatives or the allocation matches a mathematical lower bound. There may be several allocations with the same minimum reel count; the tool does not also promise the best remainder shapes or fewest cutting operations.

To keep automatic calculation responsive, input is limited to 18 individual required runs and 12 existing pieces, with at most 100,000 search states. Counts expand into individual runs or pieces before those limits are checked. If the search reaches its bound, a complete feasible allocation is retained where available and explicitly labelled as having an unproven minimum. It must not be described as optimal merely because it looks efficient.

Lengths and fit decisions retain exact finite-decimal cut intervals. Display precision therefore does not push a marginal run into a piece which is too short. This arithmetic precision does not establish manufacturing tolerances or measurement accuracy; keep practical usable lengths conservative according to the actual product and installation allowances.

Related tools

Lighting Energy and Running Cost

Estimate lighting kWh and usage cost with simple comparisons, mixed operating states, or different day types and seasonal schedules.

Inputs and results
Inputs
Counts, input W, non-overlapping state hours, specified days and optional usage rates; group IDs and mutually exclusive day-type counts where used.
Results
Energy in kWh and conditional usage cost in AUD; simple-mode A-minus-B differences or combined state/day-type totals.

Lighting Schedule Totals

Add counts, matching luminaire output and input power across groups, with separate lumen/lm-W and PPF/photon-efficacy quantities.

Inputs and results
Inputs
One row per group: count, complete-luminaire lm or 400–700 nm PPF µmol/s, and whole-luminaire input W.
Results
Group count, output and input totals, with combined lm/W or µmol/J and individual photon group comparisons.

LED Strip Cut-length Planner

Plan repeated identical LED strip lengths from a supplied cut interval, choosing not to exceed or to reach a target, with optional matching per-metre totals.

Inputs and results
Inputs
Target length per run in m, manufacturer cut interval in mm, rounding direction, whole run count and optional matching lm/m, W/m and LEDs/m.
Results
Cut intervals and actual length per run, shortfall or excess, total cut length and optional lm, W and LED counts on the supplied strip-rating basis.

Browse all lighting tools