Paired Daylight Factor

Calculate the indoor-to-outdoor horizontal illuminance ratio under declared overcast daylight measurement conditions.

Calculate a paired daylight-factor ratio from simultaneous indoor and unobstructed outdoor horizontal-plane illuminance under an applicable overcast sky.

Results update as you edit.

Calculating needs JavaScript. The form becomes available when its script is ready; the guide below is always readable.

Calculation inputs

Calculation inputs
Zero or more on the declared horizontal working plane, artificial lighting off and direct sun excluded.
Greater than zero on an unobstructed horizontal plane under the same overcast sky.
A ratio of unrelated readings is not this daylight-factor measurement.

Continue your task

Keep the percentage with its paired readings and conditions. An indoor reading above the outdoor reference needs investigation, not a target verdict.

If this answers your question within the model’s limits, record the original inputs, unrounded result and conditions. Otherwise choose an action only when its condition applies:

See this task in the decision tree

Opening another tool does not transfer or store your entries. Keep the original values, units and conditions with the next calculation.

Pair the indoor reading with the same outdoor sky

A daylight factor expresses indoor daylight as a percentage of a simultaneous outdoor reference. In the daylight-factor definition, the indoor reading is on the working plane and the outdoor reference is on an unobstructed horizontal plane under an overcast sky. This tool evaluates that declared pair with artificial lighting off and direct sun excluded.

DF = indoor daylight illuminance ÷ outdoor illuminance × 100%.

Both readings use lx, so their units cancel. An outdoor value measured at a different time or behind an obstruction changes the denominator without necessarily describing the sky illuminating the room. A convenient outdoor reading is not automatically a valid reference.

Interpret the percentage against the actual readings

For an artificial pair of 200 lx indoors and 10,000 lx outdoors, DF = 200/10,000 × 100 = 2.00%. This is a ratio for the stated point and conditions, rather than a recommended value or a verdict about the room.

  • If both readings double together, the ratio stays 2.00%.
  • If the indoor reading is 100 lx while the outdoor reference remains 10,000 lx, the ratio is 1.00%.
  • Zero indoor daylight gives 0.00%. A zero outdoor reference makes the ratio undefined and is rejected.

The display uses two decimal places; a positive ratio below 0.01% is marked below display precision. Display rounding does not alter the underlying comparison with the outdoor reference.

A value above 100% needs a condition check

The calculator retains a mathematically valid ratio above 100% and flags it for review. Check whether artificial light or direct sun entered the indoor reading, the outdoor sensor was shaded, the readings were simultaneous, the ranges and units matched, and the instruments were appropriate. The warning does not identify which condition caused the result or certify a corrected reading.

Keep the survey question narrower than annual performance

One pair of readings does not describe every location or the entire year. Seasonal sun positions, weather, shading, room surfaces and window conditions can change actual daylight. A daylight factor is also separate from glare, heat gain, electric-light savings and annual climate-based daylight measures. This calculator supplies no Australian target, standard clause or pass/fail classification.

Use illuminance conversion when instruments report different units, preserving the measurement conditions. Meter specification range can interpret a compatible single-reading specification; it does not combine the uncertainty of this two-reading ratio. For several points, retain their individual readings and representative areas before using sample statistics.

Related tools

Illuminance Meter Specification Range

Apply your instrument’s additive reading-percentage and display-count specification to an illuminance reading.

Inputs and results
Inputs
Reading in lx, percentage of reading, additional display counts, resolution in lx/count and specification conditions.
Results
Additive tolerance allowance and a nonnegative specification band in lx, without a confidence claim.

Illuminance Unit Converter

Convert the same illuminance between lux, kilolux and foot-candles, with metric units shown first.

Inputs and results
Inputs
A nonnegative illuminance and its unit: lx, klx or fc.
Results
The same illuminance in lx, klx and fc.

Illuminance Sample Statistics

Summarise spatial lux or PPFD samples with a supplied reference, or describe daylight occupied-time coverage with missing periods kept explicit.

Inputs and results
Inputs
Same-basis spatial lux/PPFD and represented areas, or daylight-only zone/time records, occupied horizon and user threshold.
Results
Spatial descriptive statistics and reference shares, or daylight area-time coverage bounds, observed mean and recorded exposure.

Browse all lighting tools