Projector Throw Distance and Image Size

Calculate nominal projector distance or image dimensions from a supplied matching throw-ratio range and image aspect ratio.

Calculate projector geometry

Use a matching manufacturer throw-ratio range to relate the complete image width to the nominal lens-to-screen distance. All distances and image dimensions below are in metres.

Results update as you edit.

Calculating needs JavaScript. These inputs become available when their script is ready; the guide below is always readable.

Projector geometry inputs

Projector geometry inputs; all active fields are required

All active fields are required. Enter decimals without commas or exponent notation.

Choose a nominal distance range or the complete image dimensions at a known lens-to-screen distance.
Use the complete projected rectangle, including any black borders around the content.
Use the width-to-height ratio that matches the supplied model and throw-ratio data.
Required positive distance ÷ image width. For a fixed lens, enter the same value in both ratio fields.
Required value at least as large as the lower ratio, from the same model, lens and image mode.
Required when using width. Measure the complete projected rectangle, not only the visible content.
Record the source, model, lens, image and zoom conditions, and the lens-to-screen reference point. Do not join limits from different models or modes.
This declaration does not verify the inputs. Ultra-short-throw, oblique projection, lens shift, digital zoom and keystone correction are outside this calculator.

Continue your task

Keep the ratio source and image mode with both range endpoints. Compare the nominal geometry with the model-specific distance table and test the actual equipment before permanent positioning.

If this answers your question within the model’s limits, record the original inputs, unrounded result and conditions. Otherwise choose an action only when its condition applies:

See this task in the decision tree

Opening another tool does not transfer or store your entries. Keep the original values, units and conditions with the next calculation.

Throw ratio connects distance to image width

If a projector specifies a throw ratio of 1.5:1, its nominal projection distance is 1.5 times the width of the matching projected image. A 2 m wide image therefore corresponds to 3 m. The ratio uses width, even when a screen is sold by its diagonal size. BenQ’s explanation of projector optics defines throw ratio as lens-to-screen distance divided by screen width.

For throw ratio T, distance D and image width W, all lengths in the same unit:

T = D / W, so D = T × W and W = D / T.

Use the manufacturer’s distance reference for the exact model and lens. Distance from a cabinet edge, wall or mounting bracket is not interchangeable with lens-to-screen distance. This calculator supports the nominal ratio relationship for a matching rectangular image; ultra-short-throw offsets, angled projection and digital image corrections need the manufacturer’s own geometry.

Why a range reverses when solving image size

A lens with a specified optical zoom range may have two throw-ratio limits. At a fixed width, multiplying by the smaller ratio gives the shorter distance. At a fixed distance, dividing by the larger ratio gives the smaller width. Using the endpoints in the same order for both operations would give the wrong size range.

The following invented example uses a matching 4:3 full projected image and a supplied ratio range of 1.2–1.5. It is not a specification for a real projector.

Known dimension Calculated range
Image width 2 m Distance 2.40–3.00 m; image height 1.50 m and diagonal 2.50 m
Lens-to-screen distance 3 m Image width 2.00–2.50 m; height 1.50–1.88 m; diagonal 2.50–3.13 m
Image diagonal 2.5 m at 4:3 Width 2.00 m and the same 2.40–3.00 m distance range

The unrounded upper height in the second row is 1.875 m and the diagonal is 3.125 m. Display rounding does not change the calculations. For a fixed-ratio lens, enter the same value at both ratio limits. A range must describe the same model, lens and image mode; combining limits from different products does not create an available zoom range.

Diagonal size needs the matching aspect ratio

Aspect ratio describes image width relative to height. For a width-to-height ratio a:b and diagonal d, Pythagoras gives:

W = d × a / √(a² + b²) and H = d × b / √(a² + b²).

At 4:3, the familiar 3–4–5 triangle makes a 2.5 m diagonal image 2 m wide and 1.5 m high. At another aspect ratio, the same diagonal has a different width, which changes the calculated distance. The available selections here are 16:9, 16:10 and 4:3; each still needs a throw ratio that applies to that full projected-image mode.

The dimensions describe the complete projected rectangle to which the supplied ratio applies. A film within black bars may occupy only part of it. Entering the smaller content diagonal with a ratio for the full image mixes two different dimensions. Likewise, keystone correction or digital zoom can change the visible picture without following the simple optical relationship.

Use the result alongside the model’s distance table

The calculated interval is a nominal geometric range. It does not establish that every image size inside it is within the lens’s focus range, or that a proposed mounting location has the required ventilation, offset and clearances. Keep those checks tied to the actual equipment instructions.

The BenQ EH620 manual, pages 14–15 illustrates why the model-specific table matters: it labels the image aspect ratio, shows the lens reference, treats measurements as approximate and calls for an in-situ test with the actual projector before permanent installation. Rounded published ratios and dimensions can also produce small differences from a manufacturer’s table. A calculated distance is therefore a starting dimension to check, rather than an exact mounting mark.

Changing image size also raises questions about screen brightness and viewing conditions, but throw ratio contains no luminous-flux or screen-reflection data. With independently established screen-delivered white-light output and matching directional gain, the Projector Screen Brightness Calculator can budget conditional white-image luminance under a uniform screen model. For an ordinary circular lighting-beam outline, use Beam Spread Geometry; its angle-based model describes a different geometry and does not replace a projector’s throw ratio.

Related tools

Beam Spread Geometry

Solve ideal circular beam geometry on a perpendicular plane, or a tilted cone’s finite ellipse. Geometry does not establish lighting adequacy.

Inputs and results
Inputs
Full cone angle, axial distance or perpendicular diameter; tilted-ellipse mode also requires axis tilt from the plane normal.
Results
Conditional circle geometry, or ellipse major/minor diameters, area and centre offset.

Projector Screen Brightness Calculator

Estimate conditional screen luminance from delivered white-light output, image area and matching directional gain, or solve a supplied luminance target for delivered lumens.

Inputs and results
Inputs
Image width and height in m, directional screen gain, screen-delivered lm or area-average projector-only lx, or a target in cd/m², with matching source and model conditions.
Results
Conditional white-image cd/m² and approximate fL, average lx and screen-delivered lm; no ambient-contrast or suitability verdict.

Browse all lighting tools