Maintenance Factor Composition

Multiply four supplied maintenance components on a matching basis without choosing product data or a cleaning schedule.

Combine four supplied factors for the same operating period and maintenance plan. These inputs are fractions, not percentages; no recommended values are selected.

Results update as you edit.

Calculating needs JavaScript. The form becomes available when its script is ready; the guide below is always readable.

Calculation inputs

Calculation inputs
A fraction greater than 0 and no more than 1, for output depreciation over the declared operating period.
A fraction greater than 0 and no more than 1, matching the declared failure and replacement assumptions.
A fraction greater than 0 and no more than 1, matching luminaire soiling and cleaning conditions.
A fraction greater than 0 and no more than 1, for the matching room and surface maintenance conditions.
Record product/method sources or explicit assumptions, operating hours, cleaning and replacement plan. Kept only in this page.

Continue your task

Carry the unrounded combined MF and its maintenance basis into the matching maintained-average calculation.

If this answers your question within the model’s limits, record the original inputs, unrounded result and conditions. Otherwise choose an action only when its condition applies:

See this task in the decision tree

Opening another tool does not transfer or store your entries. Keep the original values, units and conditions with the next calculation.

Maintenance losses are multiplied

A maintained light level accounts for changes between the initial condition and the condition represented by a maintenance plan. Output depreciation, failed lamps, luminaire soiling and room-surface changes do not describe the same loss. Page 2 of NATSPEC TECHnote DES 049 gives the four-component relationship used here:

MF = LLMF × LSF × LMF × RSMF.

Each factor is a fraction of the level remaining at its corresponding stage, greater than zero and no more than one in this model. They need a consistent operating period, cleaning policy and replacement assumption. The calculator combines supplied values; it does not select them from an IP rating, product lifetime label or room type.

Component What its input represents
LLMF Lumen maintenance of the light source over the declared operating period
LSF Survival under the declared failure and replacement assumptions
LMF The luminaire’s maintenance condition, including applicable soiling and cleaning
RSMF The effect of the matching room-surface maintenance conditions

An integrated LED luminaire may have data and maintenance conventions that differ from a replaceable-lamp system. Establish how the supplied method treats those effects before assigning a factor. A convenient value of 1 means an effect is assumed to cause no reduction in this calculation; it is not a way to mark missing information.

Reproduce an artificial factor product

Assume LLMF = 0.9, LSF = 1, LMF = 0.8 and RSMF = 0.95, all on a common declared basis. These values are invented for the example.

MF = 0.9 × 1 × 0.8 × 0.95 = 0.684, displayed as 0.6840.

The reduction from the initial level is (1 − 0.684) × 100 = 31.60%. Adding component reductions instead would give 10% + 0% + 20% + 5% = 35%, which is not the product model. Each successive fraction acts on the level remaining, rather than independently removing a percentage of the original total.

Apply the factor once on the right basis

The lumen-method estimate expects initial complete-luminaire output and one matching maintenance factor. If the entered output already includes the same depreciation or dirt loss, applying that loss again understates the modelled maintained level. Record what is included in the output data, the UF and the MF.

A calculation that retains four decimal places cannot make uncertain maintenance assumptions precise. Source data, operating hours, environment, cleaning and replacement practice determine whether the factors represent the installation. Same-condition illuminance readings can describe observed samples; they do not by themselves validate the original maintenance plan or identify which component caused a change.

Related tools

Room Index and Working-plane Geometry

Calculate rectangular area, luminaire-to-plane height and room index from dimensions measured on a common basis.

Inputs and results
Inputs
Room length and width, source and working-plane heights in m, with a shared level datum.
Results
Area in m², height above the working plane in m and dimensionless room index K.

Lumen Method Estimate

Estimate average maintained illuminance with declared UF/MF, or use a separate supplied photon-delivery budget for average PPFD and count.

Inputs and results
Inputs
Working-plane area in m², initial whole-luminaire lm, UF/MF fractions, count or target lx, and recorded assumptions.
Results
Conditional average maintained lx, or a rounded-up luminaire count and its modelled average.

Illuminance Sample Statistics

Summarise spatial lux or PPFD samples with a supplied reference, or describe daylight occupied-time coverage with missing periods kept explicit.

Inputs and results
Inputs
Same-basis spatial lux/PPFD and represented areas, or daylight-only zone/time records, occupied horizon and user threshold.
Results
Spatial descriptive statistics and reference shares, or daylight area-time coverage bounds, observed mean and recorded exposure.

Browse all lighting tools