Lighting Operational Emissions

Calculate factor-based electricity emissions and an optional baseline difference, keeping the factor source and accounting boundary explicit.

Multiply lighting electricity use by a supplied matching electricity emissions factor. No Australian state, year, factor or accounting method is selected for you.

Results update as you edit.

Calculating needs JavaScript. The form becomes available when its script is ready; the guide below is always readable.

Calculation inputs

Calculation inputs
Zero or more for the declared period and boundary, matching the factor’s energy basis.
Zero or more. Verify source, edition/year, region, method and scope. Convert g or tonnes first; do not add a scope twice.
Zero or more on the same period and service boundary. Both scenarios use the supplied factor; blank omits the comparison.
Record enough detail to identify the factor and its applicability. An artificial example is not a current Australian factor.

Continue your task

Keep kg or tonnes CO₂e and any signed baseline difference with the factor basis. The calculation chooses no factor and makes no offset claim.

If this answers your question within the model’s limits, record the original inputs, unrounded result and conditions. Otherwise choose an action only when its condition applies:

See this task in the decision tree

Opening another tool does not transfer or store your entries. Keep the original values, units and conditions with the next calculation.

Match the electricity factor to the energy

This calculation attaches a supplied emissions factor to a measured or estimated quantity of electricity. Its output is conditional on that factor’s source, year, region, accounting method and included scopes. The Australian Government publishes annual National Greenhouse Accounts Factors; use the relevant edition and its detailed applicability instructions when selecting a factor.

The calculator does not select a national average, state value or accounting method. A factor entered as kg CO₂e/kWh must already cover the boundary you intend to calculate. Do not add another factor for a scope already included, or substitute a factor in grams or tonnes without converting it.

Operational emissions (kg CO₂e) = electricity (kWh) × factor (kg CO₂e/kWh).

Divide the result by 1,000 for tonnes CO₂e. CO₂e expresses the factor’s greenhouse-gas equivalence basis; this arithmetic does not independently construct it from individual gases.

Compare a common period and factor

Suppose an artificial lighting schedule uses 450 kWh and an invented factor is 0.7 kg CO₂e/kWh. These numbers are for checking multiplication, not an Australian emissions-factor recommendation.

Item Arithmetic Result
Current scenario 450 × 0.7 315.00 kg CO₂e
Mass in tonnes 315 ÷ 1,000 0.3150 t CO₂e
Optional baseline at 750 kWh 750 × 0.7 525.00 kg CO₂e
Baseline minus current 525 − 315 210.00 kg CO₂e

A negative difference means the current scenario has higher factor-based emissions. Both scenarios use the same supplied factor. Comparing different years, regions or accounting methods needs separate reasoning; this common-factor difference does not isolate all those changes.

The display rounds kilograms to two decimal places and tonnes to four. Tiny nonzero results receive a below-precision marker. Display rounding is not used to calculate the difference. A genuinely applicable zero factor gives zero; a blank factor leaves the result unavailable.

What the result can support

The energy and running-cost tool can supply lighting kWh for a declared period. Preserve its schedule and boundary when carrying that energy here. A lower energy estimate still requires comparable lighting service before it supports a replacement decision.

The result covers only operational electricity emissions included in the factor. Manufacturing, transport, replacement, disposal and other impacts are outside it unless separately evaluated. It does not establish an offset, renewable-energy claim, complete organisational inventory or whole-life advantage. For a separate financial view, ownership cost budgets the stated cost components without treating dollars as a carbon measure.

Related tools

Lighting Energy and Running Cost

Estimate lighting kWh and usage cost with simple comparisons, mixed operating states, or different day types and seasonal schedules.

Inputs and results
Inputs
Counts, input W, non-overlapping state hours, specified days and optional usage rates; group IDs and mutually exclusive day-type counts where used.
Results
Energy in kWh and conditional usage cost in AUD; simple-mode A-minus-B differences or combined state/day-type totals.

Lighting Ownership Cost

Add upfront, electricity, maintenance and planned replacement costs, or compare two lighting options with a supplied real discount rate.

Inputs and results
Inputs
Luminaire data, whole-year horizon, constant AUD costs and replacement plan; comparison adds an alternative, real annual discount rate and comparable-service declaration.
Results
Undiscounted budget, or both options’ present cost components and a signed baseline-minus-alternative difference on the same horizon.

Lighting Schedule Totals

Add counts, matching luminaire output and input power across groups, with separate lumen/lm-W and PPF/photon-efficacy quantities.

Inputs and results
Inputs
One row per group: count, complete-luminaire lm or 400–700 nm PPF µmol/s, and whole-luminaire input W.
Results
Group count, output and input totals, with combined lm/W or µmol/J and individual photon group comparisons.

Browse all lighting tools