A daily amount needs more than one light reading
Daily light integral, or DLI, is the quantity of photosynthetically active photons arriving at a surface over a day, expressed in mol·m⁻²·day⁻¹. PPFD is their arrival rate in µmol·m⁻²·s⁻¹. Purdue’s DLI guidance explains why both light intensity and duration matter: the same midday reading can belong to days with very different morning, afternoon and cloud conditions.
For a period with a representative mean PPFD P lasting h hours, its contribution is DLI = P × h × 0.0036. The factor converts hours to seconds and micromoles to moles: 3,600/1,000,000 = 0.0036. Add the contributions from nonoverlapping periods to obtain the entered baseline. A hypothetical 300 µmol·m⁻²·s⁻¹ maintained for 12 hours contributes 12.96 mol·m⁻²·day⁻¹.
A representative mean may come from suitably sampled measurements over the stated period. An isolated instantaneous reading is not automatically that mean. A missing period is also not a measurement of zero light. Keep the measurement position, dates, sampling coverage and any genuinely zero-light periods with the baseline. Results apply to that receiving position; an average daily dose at one point does not describe every plant in an unevenly lit area.
Close the gap with additional photons
The plan compares a supplied target with the existing baseline:
Gap = max(target DLI − baseline DLI, 0)
At a constant incremental supplement PPFD S, required supplement hours = gap/(S × 0.0036). “Incremental” means the additional light from the supplement at the same receiving position. If the baseline already includes those photons, adding them again overstates the planned total. A supplement can operate while daylight is present, provided its entered PPFD is the added contribution and the baseline excludes that additional contribution.
An artificial target of 18 and a baseline of 7.2 leave a gap of 10.8 mol·m⁻²·day⁻¹. At an incremental 250 µmol·m⁻²·s⁻¹, each hour adds 0.9 mol·m⁻², so closing the gap requires 12 hours. These invented values illustrate arithmetic; the target is not a recommendation for a crop or growth stage.
DLI values in the table are mol·m⁻²·day⁻¹. The plan uses only enough of an adequate window to close the numerical gap. An insufficient window remains insufficient; it is not automatically extended. With zero incremental PPFD, a positive gap cannot be closed. If the baseline already meets the target, the required additional time is zero.
Keep the target and time window separate
The target determines the numerical daily gap. The allowable window is a separate input: a daily amount alone does not establish a suitable photoperiod, peak PPFD or lighting schedule. Keep the target’s source and its plant, growth-stage and environmental conditions alongside the result. The calculation does not infer those conditions from a plant name or choose a target for Australian growing conditions.
Displayed hours are rounded to two decimal places, while the feasibility check retains the entered decimal quantities. For example, a gap of 12 at 250 µmol·m⁻²·s⁻¹ requires 13⅓ hours. A window of 13.33 hours is slightly shorter even though the required time also displays as 13.33. A small remaining gap is still a gap; a rounded display is not a reason to treat it as zero.
Use photon measurements on a matching basis
Lux weights light for human photopic vision; PPFD counts photons in the stated photosynthetic band. Apogee’s conversion discussion shows that their relationship depends on the spectrum. A universal lux-to-PPFD factor would conceal that dependence. Use an appropriate quantum measurement or matching spectral information, retaining the sensor’s spectral response, calibration and position.
The operating time can then support an electricity and running-cost estimate, using the complete lighting system’s actual input watts. PPFD is a receiving-plane quantity; multiplying it by hours does not reveal the luminaire’s electricity use or the driver’s losses.